If you are unfortunate enough to have to test your home for mold, you are probably thinking that this is going to be a pretty inconvenient thing to have to do. Well, it might not be fun to think that you have disease-causing mold living in your house, but doing the actual test to determine if it exists is not really that hard to conduct at all. Whatever kind of test kit you end up using, the directions on the package must be followed to the exact letter or you will probably render the test useless. There are a few quite general rules that you should follow to get the most out of your testing kits.
If you can see the mold growing in your wall, ceilings, carpet, or on anything else in the home, you do not really have to do any guesswork as to whether you need to test the home or not. If you see anything like this, do not only test that room; test your entire home. Every room needs to be tested and this includes the ventilation system, because it extends to every room in the house and if mold is growing in the vents, it will spread to the rest of the house.
Run the air conditioner or fans in every room in your home before you put out the test kits so that if there are any mold spores in the room, they will be stirred
up into the air and will settle down in the kit. Do not set them up anywhere high; a coffee table or somewhere around the mid to low level of the room should be fine. If you set them up too high, you may not get a good sample.
If there happens to be mold growing visibly on anything, you can use a piece of scotch tape to lift the mold up off the surface and place it into the test kit. There is a method that you can use involving scraping some of the mold into the kit with a knife, but since this can stir up mold spores even more, unless you are wearing a respirator, you are probably better off using the tape method.
To test the ventilation system, the best thing that you can do is tape a test against the grill of one of the ventilation ducts so that the air coming out of it is hitting the testing kit at a 90 degree angle. This will allow you to get the maximum amount of exposure.
Jim Corkern is a writer and promoter of
Texas Water Damage Restoration and
Houston Water Damage Restoration Which are Certified IICRC Water damage and mold remediation contractors.
Friday, September 28, 2007
Cleaning Out Your Refrigerator
I love my food, but unfortunately, if I do not remember to keep my refrigerator cleaned out regularly, mold loves my food, too. Often people who have busy lives working and taking care of children cannot remember to clean their refrigerators out as often as they probably need to and since they have more people in the house to feed, there will also be more food. More food in the refrigerator equals more of an opportunity for bacteria and mold to grow. This is not typically a problem as long as someone keeps an inventory of what is in the refrigerator and what needs to be thrown away. You cannot completely keep mold out of your refrigerator because it exists in its spore form in the air that we breathe and unless we are talking about an extremely controlled situation like a hospital clean room, it is truly everywhere. There is not really any escaping it and while mold can grow in your fridge, you can do things to inhibit its growth rate.
Take anything that is outdated and obviously inedible out of your refrigerator and throw it away. Cleaning out everything from the refrigerator and setting it aside to go through later is a good idea when you need to clean out the entire refrigerator and sterilize it. Gather whatever chemicals you might want to use for cleaning the fridge and while this can include bleach, you might want to find another alternative that kills mold and bacteria specifically. If you only have bleach, though, go ahead and use it; just do not mix bleach with any other household chemicals.
Wash all the surfaces in the refrigerator with whatever cleaning solution you have decided on, including the racks in the door and the shelves and drawers inside the main part of the unit itself. Give it a good and thorough scrubbing. This is probably something that you should consider doing between two and three times a year or possibly more, depending on how messy your fridge gets.
When you are done cleaning the inside of the refrigerator (and the outside, if it needs it), it is time to go through what you took out. Take anything that you no longer desire and is no longer edible and throw it away. If any jars have any sticky residue on the bottoms of them, wash these off with a warm rag so you don’t get sticky grape jelly or whatever it is back on the surface of your clean fridge.
Jim Corkern is a writer and promoter of
Texas Water Damage Restoration and
Houston Water Damage Restoration Which are Certified IICRC Water damage and mold remediation contractors.
Take anything that is outdated and obviously inedible out of your refrigerator and throw it away. Cleaning out everything from the refrigerator and setting it aside to go through later is a good idea when you need to clean out the entire refrigerator and sterilize it. Gather whatever chemicals you might want to use for cleaning the fridge and while this can include bleach, you might want to find another alternative that kills mold and bacteria specifically. If you only have bleach, though, go ahead and use it; just do not mix bleach with any other household chemicals.
Wash all the surfaces in the refrigerator with whatever cleaning solution you have decided on, including the racks in the door and the shelves and drawers inside the main part of the unit itself. Give it a good and thorough scrubbing. This is probably something that you should consider doing between two and three times a year or possibly more, depending on how messy your fridge gets.
When you are done cleaning the inside of the refrigerator (and the outside, if it needs it), it is time to go through what you took out. Take anything that you no longer desire and is no longer edible and throw it away. If any jars have any sticky residue on the bottoms of them, wash these off with a warm rag so you don’t get sticky grape jelly or whatever it is back on the surface of your clean fridge.
Jim Corkern is a writer and promoter of
Texas Water Damage Restoration and
Houston Water Damage Restoration Which are Certified IICRC Water damage and mold remediation contractors.
Cleaning Out the Fridge to Prevent Mold
With the obsession that many households in the United States have with food, one would think that we would remember to keep our refrigerators cleaned a lot more often than we do. Many of us have families to take care of and jobs to tend so, so maybe it is because we just do not have time to take care of this necessary chore like we used to or perhaps we think that the problem is not as bad as we are supposed to think it is. Most people realize that bacteria and mold can grow in the refrigerator almost as easily as outside it because of the large amount of food we keep inside it and a lot of the time our food is improperly stored, which opens it to contamination even further than normal. To keep a healthy kitchen, you need to clean out your refrigerator often; clean it out completely at least once every three or four months and here is how you can start.
Remove everything from the fridge, including from the doors, and set it aside wherever you are comfortable with leaving it. The best place is on the kitchen or dining room table or just your kitchen counters. If you do not have room, set things on a table somewhere, as leaving them in the floor is not exactly practical, especially if your floor is not clean.
Take every removable part of your fridge out and set them in a sink of hot water. If you are putting glass shelves in it, rinse them with warm water first to make sure the sudden temperature change does not crack the glass. This water should also contain plenty of antibacterial soap. Allow these to soak a few minutes, especially if they have any sticky residue like from jelly or syrup.
Start washing out the inside of the refrigerator with a rag or a sponge. Use a warm bowl of water and a spray bottle of whatever chemical you have chosen for this job. You can use bleach, but do not mix it with other household chemicals that you might have on hand and always wear rubber gloves. Make sure to get any food that is stuck onto the surface of the refrigerator off before you start putting things back.
When you are done cleaning the inside and done washing the removable shelves and racks, start putting them back. Then, go through the items that you took out and throw out anything that is stale, spoiled, or contaminated with mold.
Jim Corkern is a writer and promoter of
Texas Water Damage Restoration and
Dallas Water Damage Restoration Which are Certified IICRC Water damage and mold remediation contractors.
Remove everything from the fridge, including from the doors, and set it aside wherever you are comfortable with leaving it. The best place is on the kitchen or dining room table or just your kitchen counters. If you do not have room, set things on a table somewhere, as leaving them in the floor is not exactly practical, especially if your floor is not clean.
Take every removable part of your fridge out and set them in a sink of hot water. If you are putting glass shelves in it, rinse them with warm water first to make sure the sudden temperature change does not crack the glass. This water should also contain plenty of antibacterial soap. Allow these to soak a few minutes, especially if they have any sticky residue like from jelly or syrup.
Start washing out the inside of the refrigerator with a rag or a sponge. Use a warm bowl of water and a spray bottle of whatever chemical you have chosen for this job. You can use bleach, but do not mix it with other household chemicals that you might have on hand and always wear rubber gloves. Make sure to get any food that is stuck onto the surface of the refrigerator off before you start putting things back.
When you are done cleaning the inside and done washing the removable shelves and racks, start putting them back. Then, go through the items that you took out and throw out anything that is stale, spoiled, or contaminated with mold.
Jim Corkern is a writer and promoter of
Texas Water Damage Restoration and
Dallas Water Damage Restoration Which are Certified IICRC Water damage and mold remediation contractors.
Subscribe to:
Posts (Atom)
